|
|
|
|
|
>> Installation guide
|
|
1. Insert
the microphone jack into
the control box.
2. Place
the microphone in the visor
and hide the microphone
cable through “A Pillar”
(A Frame).
Note
: Make
sure the microphone and
the cable do not interfere
with the safety of the vehicles
operation.
It
is highly recommended to
have the front of the microphone
directly facing the operator
for
the
best result.
3. Connect
the Speaker cable jack into
the main control box. Place
the speaker in the desirable
place in the front passenger
compartment. Strongly recommend
placing the speaker under
the passenger side dashboard.
Note
: Professional
installer should permanently
mount the speaker to the
safe area with the screws.
4. Connect the Remote
controller jack into the
main control box. Secure
the Remote controller near
by the driver
side
or center console with the
Velcro pads where user can
easily reach the remote
controller without compromising
safety while operating the
vehicle.
5. Place the Main control
box under the dashboard.
Note
: Professional
installer should secure
the Main control box to
under dashboard by installing
wire tie.
6. Connect the cigarette
power adaper into the cigarette
socket.
6-1. If the user wants
to install power cables
directly to the battery,
Connect the Power cable
into the car power
source
and connect the radio mute
cable. (Alternative Connection)
Professional
installation of the power
& mute cables
1)
Disconnect the power cable
from the car battery.
2)
Connect the ground wire
to the car ground.
3)
Connect the power wire to
the ignition.
4)
Connect the audio mute-1
& 2 wire to the audio
head unit.
5)
Connect the power cable
from the car battery.
6)
Turn the ignition ON and
confirm that the power of
the SJ401A(DuFree DX) is
on (Green LED-on).
7)
Turn on the audio and check
if you can hear the radio.
a)
If so, you are successfully
installed the SJ401A unit
into the car.
b)
If there is no sound, disconnect
the power cable from the
car battery and then change
the
audio
mute-1 wire to the audio
mute-2 wire and the audio
mute-2 wire connect the
audio head unit.
Note
: The
car audio manufacturers
use either the high or low
audio mute level. Therefore,
it is necessary to
check
the audio mute level. The
audio will automatically
mute upon receipt or during
the phone
conversation
and then return to the previous
volume level after completion
of the phone conversation.
If
you want to connect by a
cigarette power adapter,
you can alternate use it
for cigarette power connection.
|
|
|
>> Pairing
your Bluetooth cellular phone with the DuFree
DX (SJ401A)
|
|
Follow
the pairing instruction for the first use,
after that the unit will pair automatically.
Pairing
as the handsfree mode
When power is on (confirmed by blue LED
light), press the VOL(+) button for 5 seconds
on the Remote
controller. You
will hear a beep tone. The Handsfree device
is ready to be paired with the mobile phone.
Mobile
phone manual pairing
1. Browse
the mobile phone menu and find the connectivity
and / or Bluetooth connection section.
2. Select
the search for a new Handsfree device and
allow the mobile to find the SJ401A.
Note:
Each mobile phone
has a different phone menu so you may need
to refer to your manufacturers
instructions
to find how to connect a new Bluetooth device.
3.
The Bluetooth code for the SJ401 should
appear on your mobile phone screen.
4. Press
the conenect button with the handsfree option
on your mobile phone.
Note:
Please return to the
pairing instructions if the Bluetooth code
does not appear on the mobile
phone
screen. The green LED light should flash
during pairing.
5. The
mobile phone should prompt for the pin code.
Insert the SJ401A pin
code 1 2 3 4 by using the mobile
phone
pin code.
6. The mobile phone
should confirm that it is establishing new
connection.
7. Close the
menu. The pairing is now complete.
Note:
The green LED light
illuminates after successful pairing.
Please
adjust the volume to your preference by
using the volume keys.
|
|
|
|
>> Using
the Dufree DX (SJ401A) as a Handsfree Device
|
|
◆
When the Handsfree
is ringing ;
To
accept call press
TALK
button
To
reject call double
click
TALK button
To
end call
press
TALK button
To
control volume press
VOL+
/ VOL-
button
Audio
transfer ;
The
audio transfer function is for switching
the call from Handsfree to the mobile phone
for the private
conversation
without disconnecting the call.
Switching
from Handsfree to mobile phone
: Press and hold
TALK button (3 seconds)
Switching
back to Handsfree : Press and
hold
TALK button (3 seconds)
When
the Handsfree is idle ;
Voice
dial : Press and hold
TALK button (3
seconds) / Announce name after a beep.
Note:
This function works
if phone has the voice dialing capability.
Last
number redial : Double click on
TALK button. Announce name after a
beep.
Note:
This function works
if phone has the last number dialling feature.
|
|
>> Installation Microphone
|
|
The user can change position of the mike
depending on the vehicle type for the best
sound quality. It is also highly recommended
for user to place correct side of the mike
directly facing the user (side with more
holes). The user can place the mike either
front or back of the visor by detaching,
rotating and reattaching mike holder to
correct side of the mike.
|
|
PAIRING
INSTRUCTION FOR THE SMART PHONES
Note
:
A)
Some of the advanced features such as
the voice caller ID would not properly work
with the smart phones featuring the HEADSET
Profile only.
B) It is common
for most of the smart phones have the extra
security feature (similar to the firewall
in the computer network system) requiring
users to PAIR the smart phones with the
Bluetooth devices first and then go back
to the connection feature in the phone menu
to Authorize the Bluetooth device to be
permanently CONNECTED with the handsfree
system.
Let's try to pair the smart phones to
the DuFree DX (SJ401A) handsfree unit
as the HANDSFREE profile first!
Please
follow the below Initial pairing instruction.
1.
Make sure that the smart phone battery is
fully charged.
2. Clear/delete all Bluetooth
devices registered in your smart phone.
Also, turn
off the unit and take out the battery (reset)
and reinsert the battery and turn on the
unit.
3. Turn on the power of the DuFree
DX (SJ401A) handsfree unit.
4. Turn on the Bluetooth
on the smart phone by following the smart
phone manual.
5. Press Vol(+) button
of the DuFree DX (SJ401A) handsfree
unit for 5 seconds and wait for the confirmation
melody.
6. Discover
the DuFree DX (SJ401A) handsfree units on your
smart phone.
7. Once your smart phone
discovers the DuFree DX (SJ401A) handsfree
unit, enter the Authentication Passkey
complete pairing.
8.
If there is no connection, go back to the
Bluetooth Settings in your smart phone.
Services tab and make
sure
that the DuFree DX (SJ401A) handsfree unit
is AUTHORIZED to be paired with your smart
phone.
You will hear
the paired confirmation melody once DuFree
DX (SJ401A) handsfree unit is paired with the
smart
phone.
*Pairing with
the headset mode,
the DuFree DX (SJ401A) handsfree unit does not
support the CALLER ID features.
Please repeat
the step 1 to 4.
COMPATIBILITY:
The
DuFree DX (SJ401A) Handsfree products are compatible
with most Bluetooth equipped mobile phones.
The DuFree DX (SJ401A) Handsfree products
support most of the Bluetooth mobile phones
features such as the last number dialing,
Audio transfer, Caller ID, etc if the Bluetooth
mobiles contains such features.
Must
Power off for vehicles with the DC auxiliary
power jack feature:
Some
vehicles continuously supply 12 Volt DC
power to the auxiliary power jack (cigar
jack) even the engine is off and the ignition
key is out of the vehicle.
The user must
pull out the power jack cord before exiting
the vehicle making sure the Bluetooth unit
power is off. Otherwise, either the phone
or handsfree would not function properly
requiring the user to turn both phone and
handsfree off and reconnect by following
the manual.
|
|
|
|
>> Troubleshooting
|
|
No
indication from unit?
There
is a chance the unit power adapter is not
properly sit in the cigar/utility jack socket
so please reinsert the unit into the cigar/utility
jack.
Experiencing
problem
during pairing?
Repeat
pairing according to the pairing
section
Still
experiencing problem?
Please
turn off the mobile phone and separate the
battery from the mobile phone for about
five seconds and then repeat pairing following
the pairing instruction. (Sometimes, there
could be a bug in the mobile phone that
requires to be eliminated before pairing.)
Too
loud?
Please adjust
the volume to your preferred sound level
by pressing the volume switches.
People
are complaining about hearing noise?
Please
check if the mike is secured in place not
creating vibration and noise. Also
check and adjust front of the mike facing
toward to the user’s face.
|
|
>> Safety Precautions
|
|
- Do not expose
this unit under humid environment.
-
Do not drop this unit.
- Do not disassemble
this unit.
- Do not press two buttons
at once. This action might cause sudden
Bluetooth disconnection.
- Do not clean
the unit with any chemical or water.
-
Keep this unit away from fire and dust.
-
For safety reasons, please keep your phone
conversation short, do not make any notes
or read documents.
It
is highly recommended to park the vehicle
in the safe place before continuing the
conversation.
Using
mobile phone while driving creates a distraction
to the drive which may increase the
likelihood of an
accident.
- Please adjust direction
of the portable type unit not interfering
with safety of driving.
|
|
*
The instruction of this manual may be different
from some Bluetooth phones
according
to the phone’s manufacturer or its unique
function.
|
|
>> Warranty
|
|
ModooTronix Inc. warrants to purchaser
that for a period of one (1) year after
the date of purchase (the “Warranty Period”)
of any ModooTronix Inc. Product by Purchaser,
the product will substantially conform to
ModooTronix Inc. published specifications
for the product on the date of purchaser’s
purchase of the product, subject to the
terms herein. Purchaser shall notify ModooTronix
Inc. of any non-conformance during the warranty
period and obtain a written return material
authorization (“RMA”) from ModooTronix
Inc. for the nonconforming product and return
the nonconforming product to ModooTronix
Inc., freight prepaid with a statement describing
the nonconformity. ModooTronix Inc.
exclusive obligation with respect to nonconforming
product shall be, at ModooTronix Inc.‘s
option and expense, to repair or replace
such returned item. The foregoing is purchaser’s
sole and exclusive remedy for breach of
warranty by ModooTronix Inc.‘s with respect
to the product. The warranty set forth above
shall not apply to any product, which has
not been properly used or handled in accordance
with the instructions supplied by ModooTronix
Inc. In addition, ModooTronix Inc. ‘s warranty
is void if the product has been repaired,
altered, damaged by the faulty installation,
misuse, abuse, or which the product defect
is attributable to any failure or damage
which is beyond the reasonable control of
ModooTronix Inc. This warranty applies only
to new ModooTronix Inc. products purchased
from authorized retail sellers only. The
foregoing warranties are the sole warranties,
express or implied, given by ModooTronix
Inc. in connection with the product, and
ModooTronix Inc. disclaims all other warranties,
including warranties of merchantability,
fitness for a particular purpose and no
infringement of third party rights.
ModooTronix Inc. shall not be liable for
any special, incidental or consequential
damages in connection with the product,
even if ModooTronix Inc. has been advised
of the possibility of such damages. The
liability of ModooTronix Inc. hereunder for
all claims shall not exceed the amount paid
by purchaser to ModooTronix Inc. for the
product sold rise to ModooTronix Inc.‘s
liability.
The Bluetooth® word mark and logos
are owned by the Bluetooth SIG, Inc. and
any use of such marks by ModooTronix Inc.
is under license. Other trademarks and trade
names are those of their respective owners.
|
